Tiltex is a needle punched, fiber reinforced, geocomposite, comprising of a high strength, rapid setting, cement-sand mix fixed between two layers of geotextile.

• Our Tiltex B cement-sand mix has an added anti cracking fiber enhancement. This distributed, self-reinforced, cementitious geocomposite material has dispersed basalt fibers and is an integral part of the cementitious geocomposite. These exclusive properties add durability, strength and flexibility with the ability to withstand extreme climate fluctuations.

• Tiltex B Anti Cracking GCCM replaces rip rap, stone chipping, grout blankets, shotcrete, concrete, bitumen geomembrane and other traditional erosion control products.

• Tiltex B Anti Cracking GCCM is a cost effective alternative erosion control solution with a faster construction time and greater safety controls for the Tiltex installation.

  HIGH COMPRESSIVE STRENGTH 80MPa/11,000psi+

HIGH FLEXURAL STRENGTH 16.1MPa/2235psi*

ACHIEVES 50MPa/7252psi COMPRESSIVE STRENGTH WITHIN 24 HOURS OF HYDRATION

TILTEX PRODUCT DIMENSIONS

Thickness: 7.5mm to 12.5mm/0.295” to 0.492”

Weight: 7.5 kg to 12.5 kg per m2 / 16.5 lbs to 27.5 lbs

Permeability Rating: 1 x 10-9 m/s / 3.28 x 10-9 ft/s

Roll Width & Length: Tiltex standard roll is 5m / 16’4” wide x 20m / 65’6” long

Custom widths and lengths are available.

TILTEX B -

ANTI CRACKING ENHANCEMENT

7B, 9B, 10B & 12B

• Tiltex’s highest quality product in the range.

• Includes an additional anti cracking enhancement for higher flexural strength and survivability in hyper-cold conditions.

TILTEX PLUS RANGE

• Same as Tiltex solid screen cementitious grades.

• Incorporates an engineered geomembrane in addition to the cementitious layer for lower permeability.

TILTEX SOLID SCREEN

7, 9, 10 & 12

• Tiltex solid screen product in 7.5 kg to 12.5 kg per m2 - 16.5lbs to 27.5lbs is our standard temporary erosion control system.

• Lower physical properties & no anti cracking enhancements.

• We recommend this product for short term temporary applications only due to its limited bending strength and reduced compressive strength properties.

TILTEX TURF

7, 9, 10 & 12

• Comprising of Tiltex solid screen with an artificial turf layer fully bonded to the GCCM.

TILTEX INTRODUCES SANDMAT

Tiltex is pleased to introduce SANDMAT.

A geocomposite material impregnated with a layer of quartz sand, needle punched between two layers of nonwoven geotextile fabric to form a high strength, robust protection and drainage fabric.

SANDMAT prevents erosion and displacement of subsoils for embankments, stabilization works for erosion control, levies, watercourses, estuary and coastal environments. 

The material locks in a uniform sand layer for drainage conveyance, filtration, erosion and protection.

SANDMAT is manufactured in 5.1m / 16.7 ft wide rolls by 40m / 131.2 ft long rolls for erosion & scour protection of waterways and embankments where displacement of soils requires drainage, filtration and stability. SANDMAT can also be installed vertically.

SANDMAT is regularly used under Tiltex as a cushion layer and/or subsoil drainage layer.

TILTEX vs OTHER GCCMs

Tiltex B Other GCCMs

Compressive Strength:

80MPa/11000psi+ 40MPa/5800psi

Flexural Strength:

16.1MPa/2235psi* 4-6 MPa/580 - 870psi

Tensile Strength:

>20kn/m 6.6kn/m - 8.6kn/m

both directions one direction

Width:

5 m / 16’4” 1.1m / 3’6”

Based upon a 1000m/3280ft x 10m/32.8ft wide channel:

300m2/3229ft2 1,363.5m2/4473ft2

Increase in gross material usage due to overlaps:

200 panels 909 panels

Price:

Competitive can be >30-40% higher**

Total Turn Key Solution Service:

Yes Often just supply

*tested after 7 days. See data sheet for detail

** based on market data received

The data above is average values derived from standard tests and market information are subject to usual product variation. The right is reserved to make changes without notice at any time.

UNIFORM HYDRATION IS THE KEY TO OPTIMUM PRODUCT PERFORMANCE

Tiltex North America is excited to announce the introduction of our new Saturation Hydrator.

11,000+psi / 80MPa Compressive Strength with 2235psi/16.1MPa* Flexural Strength are important qualities of our Tiltex B Anti Cracking GCCM but the product need to properly hydrated to reach its optimum performance levels.

Our engineers have designed a new Saturation Hydrator ensuring a consistent hydration after rolling out & heat sealing our 5 metre wide rolls (no screws required) so the end result is uniform 11,000+psi/80MPa Compressive Strength Concrete.